Before I get into the parts you need, I want to share some aquarium safety tips that are being developed:
Best practices for the use of lasers in aquaria (first draft)
Secure the Area
The lase area should be closed off from any transient traffic to prevent someone from unknowingly entering the area without appropriate eye protection. Any doors should be closed and locked. Any windows should be covered or blinds closed to prevent the escape of reflected laser energy.
Only the laser operator and those required in the process should be allowed in the area. All pets should be removed from the area and prevented for reentering while the laser is in use.
Protective Gear
A high power laser beam striking your eye, or the eye of an observer can result in instant and permanent blindness. Even viewing the beam endpoint without eye protection will cause eye damage. The user and everyone within the viewing or potential reflection areas must be equipped with appropriate eye protection specifically designed for the wavelength laser being used. Sunglasses do not protect against laser light. Laser eye protection is designed to protect against unintentional reflections and endpoint viewing. It is not designed to protect from a laser beam being directed toward the eye. Never look directly at a laser beam or allow it to directly strike your eye. Long sleeves and Nitrile gloves offer an additional layer of protection for the operator.
Identify and Eliminate Reflection Hazards
Using high power lasers in glass and acrylic tanks is virtually guaranteed to create potentially hazardous beam reflections. These beam reflections can cause serious injury. This danger is amplified by the fact that use of the appropriate safety goggles will prevent you from seeing most beam reflections. Positioning the laser at right angles (directly perpendicular) to the tank glass or acrylic should be avoided as unseen laser energy will be reflected directly toward the user. Burns to exposed tissue can occur within seconds.To prevent injury, a low power targeting laser (such as a laser pointer) in a different spectrum that can be seen when using the safety goggles should be utilized to identify any reflections before firing the high power laser.
Identify Backstops
The laser beam will penetrate clean glass or acrylic with virtually no heat being transmitted to the tank material. The beam will quickly (almost instantly) pierce though the targeted item and impact anything behind it. Extreme caution must be exercised to prevent injury to any livestock located behind the targeted item. Painted or dark glass or acrylic surfaces may become heated during lasing.
Reduce Water Flow
Pumps should be turned off during lasering. This limits the cooling effect of water passing over the target thereby increasing the effectiveness of the laser and reducing the firing duration required to achieve the intended results. It also simplifies targeting as the intended pest is motionless.
Protecting Tank Inhabitants
Failure to protect tank inhabitants from repeated viewing the beam endpoint will likely result in blindness to your livestock. Ideally, all livestock should be removed and held in quarantine in a tank protected (covered) from stray laser light until laser treatment is completed. Alternative methods(s) to protect livestock from encountering the beam or end-point include,
- Physical Barriers - Use of physical barriers to prevent inhabitants from accessing an area being lased and to prevent any laser energy (beam pass-through or reflections) from entering any areas containing livestock.
- Endpoint Shield - If physically blocking off the area being lased is impractical due to tank features, an end-point shield should be used to prevent inhabitants from viewing the end-beam. In this case, extreme diligence is required to extinguish the beam should any inhabitants approach. This is likely, due to curiosity over the “sizzling” sound created by the operating laser. The endpoint shield can be created by simply as a short section of opaque acrylic (such as painted or frosted.) PVC should not be used as it emits toxins when heated.
Potential Impact to Water Quality
Use of a lasers to eradicate certain marine pests may result in the release of undetermined levels of toxins into the water column. It is believed that the intense heat may break down some of the compounds (such as Palytoxins.) Depending on the type and number of pests being destroyed and the size of the tank, the user should be prepared to use fresh carbon and or execute a water change to reduce any toxins produced.
Securing the Laser When Not in Use
When not in use the laser should be treated and stored as a firearm. When not is use it should be secured in a lockable case with batteries removed. The locked case should be stored out of the reach of children.
CJ
